|
|
|
STD-302N-R 434MHz/869MHz |
Regulatory compliance of the
STD-302N-R
The STD-302N-R is designed for embedding
in other equipment. (Products
incorporating the STD-302N-R are
henceforward referred to as final
products.)
The European regulation applicable to
the STD-302N-R is the R&TTE Directive
1999/5/EC.The conformity assessment for
the STD-302N-R was completed in
accordance with the R&TTE Directive
Annex III procedures.
Cautions related to regulatory
compliance when embedding the STD-302N-R
1. Duty cycle
The STD-302N-R is designed to be used
for the Non-Specific Short Range Devices
defined in the ERC/REC 70-03 Annex 1.
The STD-302N-R continuously emits
carrier signals when power is supplied.
The user must design the final product
to meet the requirements of the duty
cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC
70-03.
2. Antenna
The STD-302N-R is supplied without a
dedicated antenna and the user is
required to provide an antenna. The
conformity assessment of the STD-302N-R
was performed using Circuit Design’s
standard antenna
ANT-LEA-01(434MHz)/-02(869MHz) (1/4
lambda lead antenna), so we recommend
using the ANT-LEA antenna or an antenna
with equivalent characteristics and
performance. If you use an antenna other
than the recommended antenna, further
radio conformity assessment may be
required.
3. Supply voltage
The STD-302N-R should be used within the
specified voltage range (3.0 V to 5.5
V).
4. Enclosure
To fulfill the requirements of EMC and
safety requirements, the STD-302N-R
should be mounted on the circuit boards
of the final products and must be
enclosed in the cases of the final
products. No surface of the STD-302N-R
should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
STD-302N-R will be exempted from its
conformity assessment procedures. For
details of how to use the conformity
assessment of the STD-302N-R, please
consult the relevant authorities or
accredited certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not necessary
if the final product is used in the
harmonized frequency band and is
classified as Class-1 equipment. If the
final product is not used in the
harmonized frequency band and is
classified as Class-2 equipment, the
manufacturer of the final product has a
duty to notify the relevant radio
regulatory authorities in the countries
where the final product is sold.
*NOTE: In case the STD-302N-R 434MHz is
used with more than a 10% duty,
notification of the final product will
be required. A list of Class-1 equipment
is available at
http://www.ero.dk/
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant countries. |
|
|
STD-302
419MHz |
|
|
|
STD-302 419
MHz was designed to be
installed in radio equipment
for use in China. However
this product has not been
assessed for conformity with
the appropriate local
regulations. Users are
required to verify that
their final product meets
the appropriate
specifications and to
perform the procedures for
regulatory compliance.
For more information, refer
to the regulatory compliance
information of 'STD-302
419MHz operation guide'. |
|
|
STD-302N 447MHz |
STD-302N 447
MHz was designed to be
installed in radio equipment
for use in Korea. However
this product has not been
assessed for conformity with
the appropriate local
regulations. Users are
required to verify that
their final product meets
the appropriate
specifications and to
perform the procedures for
regulatory compliance.
For more information, refer
to the regulatory compliance
information of 'STD-302N
447MHz operation guide'. |
|
|
STD-302
429MHz |
STD-302 429
MHz was designed to be
installed in radio equipment
for use in Japan and to meet
the specifications of
STD-T67. However this
product has not been
assessed for conformity with
the regulations. Users are
required to verify that
their final product meets
the appropriate
specifications and to
perform the procedures for
regulatory compliance.
You can find more Japanese
regulatory information at
Compliance Assessment. |
|
|
STD-302N-R
458MHz |
STD-302N-R
458 MHz was designed to be
installed in radio equipment
for use in UK and to meet
the specifications of ES300
220-1 V.1.3.1. However this
product has not been
assessed for conformity with
the regulations. Users are
required to verify that
their final product meets
the appropriate
specifications and to
perform the procedures for
regulatory compliance.
For more information, refer
to the regulatory compliance
information of 'STD-302N-R
458MHz operation guide' |
|
|
Iscrivetevi nella nostra
mailing-list inviando una E-mail
vuota a
click |
|
|
|
|
|
|
Distributore Italia SYLCOM S.r.l. - P.zza Martiri
Libertà 3, 10018 Pavone Canavese - TORINO (IT) |
|
|
|
|
|
|
|
Competence
in Radio Solution
