|
|
|
CDP-TX-05M-R/CDP-RX-05M-R 434 MHz/869
MHz |
 |
Regulatory compliance of the
CDP-TX-05M-R and the CDP-RX-05M-R
The CDP-TX-05M-R and the CDP-RX-05M-R
are designed for embedding in other
equipment. (The products incorporating
the CDP-TX/RX-05M-R are henceforward
referred to as final products.)
The European regulation applicable to
the CDP-TX-05M-R and the CDP-RX-05M-R is
the R&TTE Directive 1999/5/EC. The
conformity assessment for the
CDP-TX-05M-R and the CDP-RX-05M-R was
completed in accordance with the R&TTE
Directive Annex II (RX) and III (TX)
procedures, and the Declaration of
Conformity is attached to this manual.
Note: The CDP-TX-05M-R and the
CDP-RX-05M-R are intended to be used in
all EU and EFTA countries.
There may be some restrictions in the
following countries. For details,
consult the relevant authorities;
434MHz : FI, FR, HU, IT, LU, LI, CH
869MHz: RU, IT, HU,FR, NO, CZ, GR, LV,
SK, MK
Cautions related to regulatory
compliance when embedding the
CDP-TX-05M-R and the CDP-RX-05M-R
1. Duty cycle
The CDP-TX-05M-R is designed to be used
for the Short Range Devices (Non-specific
SRD & Alarms) defined in the ERC/REC
70-03.
The CDP-TX-05M-R continuously emits
carrier signals when power is supplied.
The user must design the final product
to meet the requirements of the duty
cycle as provided in the Regulatory
parameters related to the ERC/REC 70-03.
2. Antenna
The CDP-TX-05M-R is supplied without a
dedicated antenna and the user is
required to provide an antenna. The
conformity assessment of the
CDP-TX-05M-R was performed using Circuit
Design’s standard antenna ANT-LEA-01
(1/4 lambda lead antenna). Therefore we
recommend you using the ANT-LEA-01
antenna or an antenna with equivalent
characteristics and performance. For
details about our standard antenna,
refer to
www.circuitdesign.jp or contact us.
If you use an antenna other than the
recommended antenna, further radio
conformity assessment may be required.
3. Supply voltage
The CDP-TX-05M-R should be used within
the specified voltage range (2.2 V to
5.5 V).
4. Enclosure
To fulfill the requirements of EMC and
safety requirements, the CDP-TX-05M-R
and the CDP-RX-05M-R should be mounted
on the circuit boards of the final
products and must be enclosed in the
cases of the final products. No surface
of the CDP-TX-05M-R and the CDP-RX-05M-R
should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
CDP-TX-05M-R and CDP-RX-05M-R will be
exempted from its conformity assessment
procedures. For details of how to use
the conformity assessment of the
CDP-TX-05M-R and the CDP-RX-05M-R,
please consult the relevant authorities
or accredited certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not necessary
if the final product is used in the
harmonized frequency band and is
classified as Class-1 equipment. If the
final product is not used in the
harmonized frequency band and is
classified as Class-2 equipment, the
manufacturer of the final product has a
duty to notify the relevant radio
regulatory authorities in the countries
where the final product is sold.
The list of Class-1 equipment is
available at
http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant countries |
|
Iscrivetevi nella nostra
mailing-list inviando una E-mail
vuota a
click |
|
|
|
|
|
|
Distributore Italia SYLCOM S.r.l. - P.zza Martiri
Libertà 3, 10018 Pavone Canavese - TORINO (IT) |
|
|
|
|
|
|
|
Competence
in Radio Solution
