|
|
|
CDP-TX-04S-R 434MHz / 869MHz |
Regulatory compliance of the
CDP-TX-04S-R
The CDP-TX-04S-R is designed for
embedding in other equipment. (Products
incorporating the CDP-TX-04S-R are
henceforward referred to as final
products.)
The European regulation applicable to
the CDP-TX-04S-R is the R&TTE Directive
1999/5/EC. The conformity assessment for
the CDP-TX-04S-R was completed in
accordance with the R&TTE Directive
Annex III procedures.
Cautions related to regulatory
compliance when embedding the
CDP-TX-04S-R
1. Duty cycle
The CDP-TX-04S-R is designed to be used
for the Non-Specific Short Range Devices
defined in the ERC/REC 70-03 Annex 1.
The CDP-TX-04S-R continuously emits
carrier signals when power is supplied.
The user must design the final product
to meet the requirements of the duty
cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC
70-03.
2. Antenna
The CDP-TX-04S-R is supplied without a
dedicated antenna and the user is
required to provide an antenna. The
conformity assessment of the
CDP-TX-04S-R was performed using Circuit
Design’s standard antenna ANT-LEA-01
(1/4 lambda lead antenna), so we
recommend using the ANT-LEA-01 antenna
or an antenna with equivalent
characteristics and performance. For
details about our standard antenna,
refer to the
“Options” page in this web site or
contact us. If you use an antenna other
than the recommended antenna, further
radio conformity assessment may be
required.
3. Supply voltage
The CDP-TX-04S-R should be used within
the specified voltage range (2.2 V to
5.5 V).
4. Enclosure
To fulfill the requirements of EMC and
safety requirements, the CDP-TX-04S-R
should be mounted on the circuit board
of the final product, and must be
enclosed in the case of the final
product. No surface of the CDP-TX-04S-R
should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
CDP-TX-04S-R will be exempted from its
conformity assessment procedures. For
details of how to use the conformity
assessment of the CDP-TX-04S-R, please
consult the relevant authorities or
accredited certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not necessary
if the final product is used in the
harmonized frequency band and is
classified as Class-1 equipment. If the
final product is not used in the
harmonized frequency band and is
classified as Class-2 equipment, the
manufacturer of the final product has a
duty to notify the relevant radio
regulatory authorities in the countries
where the final product is sold.
*NOTE: In case the CDP-TX-04S-R 434.075
MHz is used with more than a 10% duty
cycle, notification of the final product
will be required. A list of Class-1
equipment is available at
http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant countries.
|
|
CDP-RX-03BS-R 434MHz / CDP-RX-03AS-R
869MHz |
|
Regulatory compliance of the
CDP-RX-03BS-R and the CDP-RX-03AS-R
The CDP-RX-03BS-R and the CDP-RX-03AS-R
are designed for embedding in other
equipment. (Products incorporating the
CDP-RX-03BS-R and the CDP-RX-03AS-R are
henceforward referred to as final
products.) The European regulation
applicable to these modules is the R&TTE
Directive 1999/5/EC. The conformity
assessment for the CDP-RX-03BS-R and the
CDP-RX-03AS-R was completed in
accordance with the R&TTE Directive
Annex II procedures.
Cautions related to regulatory
compliance when embedding the
CDP-RX-03BS-R and the CDP-RX-03AS-R
Enclosure
To fulfill the requirements of EMC and
safety requirements, the CDP-RX-03BS-R
and the CDP-RX-03AS-R should be mounted
on the circuit board of the final
product, and must be enclosed in the
case of the final product. No surface of
the CDP-RX-03BS-R and the CDP-RX-03AS-R
should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final products
incorporating the R&TTE assessed
CDP-RX-03BS-R and the CDP-RX-03AS-R will
be exempted from its conformity
assessment procedures. For details of
how to use the conformity assessment of
the CDP-RX-03BS-R and the CDP-RX-03AS-R,
please consult the relevant authorities
or accredited certification bodies.
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant country |
|
Iscrivetevi nella nostra
mailing-list inviando una E-mail
vuota a
click |
|
|
|
|
|
|
Distributore Italia SYLCOM S.r.l. - P.zza Martiri
Libertà 3, 10018 Pavone Canavese - TORINO (IT) |
|
|
|
|
|
|
|
Competence
in Radio Solution
