|
|
|
CDP-TX-02F(P)-R CDP-RX-02F(P)-R |
|
 |
| |
Regulatory
compliance of the CDP-TX-02F(P)-R
and the CDP-RX-02F(P)-R
the CDP-TX-02F(P)-R and the
CDP-RX-02F(P)-R are designed for
embedding in other equipment. (Products
incorporating the CDP-TX-02F(P)-R
and the CDP-RX-02F(P)-R are
henceforward referred to as final
products.)
The European regulation applicable
to the CDP-TX-02F(P)-R and the
CDP-RX-02F(P)-R is the R&TTE
Directive 1999/5/EC.The conformity
assessment for the CDP-TX-02F(P)-R
and the CDP-RX-02F(P)-R was
completed in accordance with the R&TTE
Directive Annex II (RX) and III (TX)
procedures, and the Declaration of
Conformity is attached to this
manual.
Cautions related to regulatory
compliance when embedding the
CDP-TX-02F(P)-R and the
CDP-RX-02F(P)-R
1. Duty cycle
The CDP-TX-02F(P)-R is designed to
be used for the Non-Specific Short
Range Devices defined in the ERC/REC
70-03 Annex 1.
The CDP-TX-02F(P)-R continuously
emits carrier signals when power is
supplied. The user must design the
final product to meet the
requirements of the duty cycle as
provided in the Regulatory
parameters related to Annex 1 of the
ERC/REC 70-03.
2. Antenna
The CDP-TX-02F(P)-R is supplied with
a dedicated antenna and the
conformity assessment of the
CDP-TX-02F(P)-R was performed using
the dedicated antenna (Circuit
Design’s standard antenna
ANT-LEA-01, 1/4 lambda lead
antenna). If you use an antenna
other than the dedicated anntena or
an antenna with equivalent
characteristics and performance,
further radio conformity assessment
may be required.
3. Supply voltage
The CDP-TX-02F(P)-R should be used
within the specified voltage range
(3.0 V to 12 V).
4. Enclosure
To fulfill the requirements of EMC
and safety requirements, the
CDP-TX-02F(P)-R and the
CDP-RX-02F(P)-R should be mounted on
the circuit boards of the final
products and must be enclosed in the
cases of the final products. No
surface of the CDP-TX-02F(P)-R and
the CDP-RX-02F(P)-R should be
exposed.
Conformity assessment of the
final product
The manufacturer of the final
product is responsible for the
conformity assessment procedures of
the final product in accordance with
the R&TTE Directive.
As to the conformity assessment of
the R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
CDP-TX-02F(P)-R and CDP-RX-02F(P)-R
will be exempted from its conformity
assessment procedures. For details
of how to use the conformity
assessment of the CDP-TX-02F(P)-R
and the CDP-RX-02F(P)-R, please
consult the relevant authorities or
accredited certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not
necessary if the final product is
used in the harmonized frequency
band and is classified as Class-1
equipment. If the final product is
not used in the harmonized frequency
band and is classified as Class-2
equipment, the manufacturer of the
final product has a duty to notify
the relevant radio regulatory
authorities in the countries where
the final product is sold.
*NOTE: In case the CDP-TX-02F(P)-R
434MHz is used with more than a 10%
duty, notification of the final
product will be required. A list of
Class-1 equipment is available at
http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not
guarantee the accuracy of the above
mentioned information about the
conformity assessment and
notification of the final product.
Directives, technical standards,
principles of operation and the like
may be interpreted differently by
the authorities in each country.
Also the national laws and
restrictions vary with the country.
In case of doubt or uncertainty, we
recommend that you check with the
authorities or official
certification organizations of the
relevant countries |
|
Iscrivetevi nella nostra
mailing-list inviando una E-mail
vuota a
click |
|
|
|
|
|
|
Distributore Italia SYLCOM S.r.l. - P.zza Martiri
Libertà 3, 10018 Pavone Canavese - TORINO (IT) |
|
|
|
|
|
|
|
Competence
in Radio Solution
