|
|
 |
 |
Regulatory compliance
of the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R are designed for
embedding in other equipment. (Products
incorporating the CDP-TX-02E(P)-R and
the CDP-RX-02E(P)-R are henceforward
referred to as final products.)
The European regulation applicable to
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R is the R&TTE Directive
1999/5/EC.The conformity assessment for
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R was completed in
accordance with the R&TTE Directive
Annex II (RX) and III (TX) procedures.
Cautions related to regulatory
compliance when embedding the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R
1. Duty cycle
The CDP-TX-02E(P)-R is designed to be
used for the Non-Specific Short Range
Devices defined in the ERC/REC 70-03
Annex 1.
The CDP-TX-02E(P)-R continuously emits
carrier signals when power is supplied.
The user must design the final product
to meet the requirements of the duty
cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC
70-03.
2. Antenna
The CDP-TX-02E(P)-R is supplied with a
dedicated antenna and the conformity
assessment of the CDP-TX-02E(P)-R was
performed using the dedicated antenna (Circuit
Design’s standard antenna
ANT-LEA-01, 1/4 lambda lead
antenna). If you use an antenna other
than the delicated anntena or an antenna
with equivalent characteristics and
performance, further radio conformity
assessment may be required.
3. Supply voltage
The CDP-TX-02E(P)-R should be used
within the specified voltage range (3.0
V to 12 V).
4. Enclosure
To fulfill the requirements of EMC and
safety requirements, the CDP-TX-02E(P)-R
and the CDP-RX-02E(P)-R should be
mounted on the circuit boards of the
final products and must be enclosed in
the cases of the final products. No
surface of the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
CDP-TX-02E(P)-R and CDP-RX-02E(P)-R will
be exempted from its conformity
assessment procedures. For details of
how to use the conformity assessment of
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R, please consult the
relevant authorities or accredited
certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not necessary
if the final product is used in the
harmonized frequency band and is
classified as Class-1 equipment. If the
final product is not used in the
harmonized frequency band and is
classified as Class-2 equipment, the
manufacturer of the final product has a
duty to notify the relevant radio
regulatory authorities in the countries
where the final product is sold.
*NOTE: In case the CDP-TX-02E(P)-R
434MHz is used with more than a 10% duty,
notification of the final product will
be required. A list of Class-1 equipment
is available at
http://www.ero.dk/
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant countries.
|
|
CDP-TX-02E(P)-R 458MHz
CDP-RX-02E(P)-R 458MHz |
 |
Regulatory compliance
of the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R are designed for
embedding in other equipment. (Products
incorporating the CDP-TX-02E(P)-R and
the CDP-RX-02E(P)-R are henceforward
referred to as final products.)
The European regulation applicable to
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R is the R&TTE Directive
1999/5/EC.The conformity assessment for
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R was completed in
accordance with the R&TTE Directive
Annex II (RX) and III (TX) procedures.
The CDP-TX-02E(P)-R 458MHz and the
CDP-RX-02E(P)-R 458MHz are designed to
be used in the 458MHz band allocated for
Industrial or commercial telemetry and
telecommand devices in UK. The
applicable technical specification is EN
300 220.
Cautions related to regulatory
compliance when embedding the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R.
1. Antenna
The CDP-TX-02E(P)-R is supplied with a
dedicated antenna and the conformity
assessment of the CDP-TX-02E(P)-R was
performed using the dedicated antenna (Circuit
Design’s standard antenna ANT-LEA-01,
1/4 lambda lead antenna). If you use an
antenna other than the dedicated anntena
or an antenna with equivalent
characteristics and performance, further
radio conformity assessment may be
required.
2. Duty cycle
The CDP-TX-02E(P)-R 458MHz continuously
emits carrier signals when power is
supplied. The user must design the final
product to meet the requirements of the
duty cycle as provided in the relevant
regulations.
3. Supply voltage
The CDP-TX-02E(P)-R should be used
within the specified voltage range (3.0
V to 12 V).
4. Enclosure
To fulfill the requirements of EMC and
safety requirements, the CDP-TX-02E(P)-R
and the CDP-RX-02E(P)-R should be
mounted on the circuit boards of the
final products and must be enclosed in
the cases of the final products. No
surface of the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R should be exposed.
Conformity assessment of the final
product
The manufacturer of the final product is
responsible for the conformity
assessment procedures of the final
product in accordance with the R&TTE
Directive.
As to the conformity assessment of the
R&TTE Directive Article 3.2 (Efficient
use of the radio spectrum), the
manufacturer of the final product
incorporating the R&TTE assessed
CDP-TX-02E(P)-R and CDP-RX-02E(P)-R will
be exempted from its conformity
assessment procedures. For details of
how to use the conformity assessment of
the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R, please consult the
relevant authorities or accredited
certification bodies.
Notification of the final product
The notification required by R&TTE
Directive Article 6 (4) is not necessary
if the final product is used in the
harmonized frequency band and is
classified as Class-1 equipment. If the
final product is not used in the
harmonized frequency band and is
classified as Class-2 equipment, the
manufacturer of the final product has a
duty to notify the relevant radio
regulatory authorities in the countries
where the final product is sold.
* A list of Class-1 equipment is
available at http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee
the accuracy of the above mentioned
information about the conformity
assessment and notification of the final
product. Directives, technical standards,
principles of operation and the like may
be interpreted differently by the
authorities in each country. Also the
national laws and restrictions vary with
the country. In case of doubt or
uncertainty, we recommend that you check
with the authorities or official
certification organizations of the
relevant countries |
|
Iscrivetevi nella nostra
mailing-list inviando una E-mail
vuota a
click |
|
|
|
|
|
|
Distributore Italia SYLCOM S.r.l. - P.zza Martiri
Libertà 3, 10018 Pavone Canavese - TORINO (IT) |
|
|
|
|
|
|
|
Competence
in Radio Solution
